Doudou DIY: tutorial to sew clothes for a stuffed rabbit

Design and production: Vania Leoy-ThuillierCreation: Nun StudioPhoto: Louis Gaillard

The tutorial for sewing smocking

Material:

Diagrams and patterns: part 1-Part 2-Part 3

Steps:

Draw the enlarged boss with chalk. Open the stitches with the ironing iron as the Assembly progresses.

Still at a loss as how to deal with this without becoming a shittier, more selfish person than I already think I am … Http: / / t.co / qVHdu8VHoq

— Acorn Queen Sun Dec 08 00:38:27 +0000 2019

Embroider at the front point with the beaded cotton. Cut 2 flowers from the flower fabric at raw.

3 fold the front of your legs backwards and backwards along the "rib" line and mark the fold with the iron. Stitch a rib seam 1 mm from the edge. Place to place, assemble back media, from crotch to marker A. assemble back to back trimmings at the handle, neckline and back middle (shoulders excluded). Cut off the corners and the corners, go back to the place and come by again.

4 assemble the front trimming on the flanges and the neckline. Crank as before and go back to the place. Place to place, assemble the sides of the tuxedo starting with the trimmings at the handle to the bottom.

5 assemble the setbacks at the bottom of the legs (Diagram 1). With iron, pull down the seam margin. Place to place, close the crotch. Cut off the corners and go back to the place. Fold the edge of the back by 5 mm and sew it in place with slippery points.

6 back medium: form a 7 mm retract on the unsewn part above A of the Dos media. Prick it up to 5 mm from the edge. Sew the pressure on the back neckline to close the tuxedo. Make a 7 mm retract on each shoulder. Side by side, assemble the shoulders in front of those of the Dos at invisible points by hand.

7 lift up the enlarged parts of the watch and the bow tie from the cardboard, and cut them out. Draw the dial of the watch with felt. Pierce the centre with the embroidery needle. Pass a double embroidery thread through the central hole and repass its ends through the buckle before sewing them at one of the backsides of the pocket. Glue the 40 cm centre of cotton yarn to the back of the bow tie and tie the thread around the rabbit's neck. Cut the bottom and edge of the hat and a rectangle 14 x 4.5 cm high. Wrap this rectangle and insert the resulting tube into the hollow hole at the base of the hat. Stick. With adhesive tape, reinforce the mounting from the inside. Stick the cap round to the top of the cylinder.

The tutorial to sew the evening dress

Material:

Diagrams and patterns: part 1-Part 2

Steps:

1 fold the fabric in half, place to place. Trace the enlarged boss with the tailor chalk. Cut the following pieces: 1 x High back, 1 x plastron (top front), 2 x Channel, 2 x skirt (cut 1 rectangle of L 28.5 x 22.5 cm wide). The seam margins are included in the pattern, the inner line indicates the seam. Open the stitches with the ironing iron as the Assembly progresses. Surround the rooms, except for the plastron.

2 place a heat-gluing veil on the back of the top front until the fold. Carry the enlarged pattern with carbon paper on the top of the room. Brock it at the back point and noose point with 2 strands of Mouline cotton. Sew seed pearls around the pattern.

3 pass 2 threads of frogs 0.5 and 1 cm from the top of the skirt in front and back. Frown. Place against place, assemble the skirt back to the top and the skirt in front with the plastron. In iron, form a 1 cm retract for the upper back slide. Sting at 7 mm. Cut the ribbon in half, insert each part on either side of the marker A. attach the ends of the ribbons to markers B and B'by rear dots.?

4 form the 2 hollow folds of the sleeves and fix them with a stitch made in the seam margin. In iron, form a 1 cm retract for the bottom of the sleeves. Prick 7 mm from the edge. Place against place, assemble the part in front of the sleeves with the plastron and the back part of the sleeves on the top back. The "free part" indicated on the pattern is not sewn on the shoulder (Diagram 2). Make a 7 mm retract on this part and sew it with slippery points.

5 cut the 20 cm of elastic in half and insert a piece into the bottom of the sleeves with the nanny pin. Place to place, close the bottom of the sleeves by sandwiching the ends of the elastic bands to block them. In the extension, close the front and back sides of the skirt. Form a double retract of 7 mm for the hem and prick it.

6 fold the band of tulle in half, in the direction of the width. Prick all along the fold at 7 mm from the edge to form a slide. Insert the 18 cm of elastic into the slide with the nanny pin. Tie the two ends of the elastic to form the collar.